Skip to content

Product / MSS

Halton MSS – Static pressure measurement unit

Comprising measurement element and pressure transmitter with LCD display.

  • Circular duct static pressure measurement unit comprising measurement element and pressure transmitter with LCD display

Static pressure measurement unit for circular ducts

Request a Quote

Overview

  • Pressure transmitter equipped with automatic zero point calibration to ensure continuous accuracy
  • Circular duct static pressure measurement unit comprising measurement element and pressure transmitter with LCD display
  • Adjustable pressure measurement range 0…1000 Pa
  • Accurate measurement, inaccuracy less than ± 10 % in typical applications
  • Pressure transmitter equipped with automatic zero point calibration to ensure continuous accuracy
  • Available in sizes Ø200 … Ø 500
  • Classification of casing leakage EN 1751 class C
  • Duct spigots have integrated rubber gaskets

Accessories

  • Integrated electronic static pressure transmitter unit

Dimensions and weight

NS L ØD
200 142 199
250 142 249
315 142 314
400 195 399
500 195 499

Weight

NS kg
200 0,9
250 1,1
315 1,3
400 2,3
500 2,9

Material

  Part   Material   Note
  Casing   Galvanised steel
  Measurement tube   Silicone
  Measurement tab   Polyurethane
  Duct gaskets   1C-polyurethane hybrid
  Transmitter Enclosure   Polycarbonate   IP54

Duct connection gaskets are vulcanised to the casing.

Function

Fig.1. Halton MSS with HDE-PE

Duct static pressure is accurately determined using multipoint averaging measurement. The duct static pressure is measured between the Halton MSS measurement tab and the reference space. The pressure of reference space represents the air pressure of the spaces in the ventilation system’s service area (see Installation section).

The Halton MSS unit includes static type pressure measurement sensor with a digital display of the actual pressure value. The measured value is transmitted using 0 to 10 volt signal.

Key:
A     Pressure measurement chamber
B     Pressure measurement tube connection points
C     Power supply and output signal.

Continuous accuracy is assured by automatic zero point calibration of pressure sensor. Thus, no manual re-calibration is needed in normal operating conditions.

Installation

The static pressure measurement unit must be installed in a space where ambient temperature is between 0 and 45°C.

Ductwork installation, safety distances

In order to ensure the accuracy of the duct static pressure, measurement the safety distances between the measurement unit and flow disturbances (e.g. bends, T-branches) must be respected. The necessary safety distances before and after different disturbances are presented in figures below.


Fig.1. 90° elbow

Fig.2. Branch on supply duct

Fig.3. Branch on exhaust duct

Fig.4. Safety distance between MDC/HFS control damper and MSS, straight duct

Measurement tube connections

Connect the pressure measurement tube from the unit to the sensor, either to +/- taps, according to the exhaust/supply application.  Supply connection is the default factory setting.

In typical installations the reference pressure inlet (+ for exhaust installation and – for supply installation) is left open at the ambient air. If necessary, the reference pressure can be connected to the reference pressure inlet by the contractor using Ø 6/4 mm measurement tubes.
Connection of measurement tube to the transmitter in supply and exhaust installations.

Electric connections
1.   Power supply, 24 VAC / 24 VDC
2.   Neutral, 0 V
3.   Output signal, 0 to 10 VDC, < 2 mA

Power supply is wired from pressure control damper.

Technical data of the pressure transmitter

Supply voltage:          22…28 VAC/VDC
Power consumption:  < 1.5 VA  24 VAC, < 1.0 VA  24 VDC

Measurement ranges:

  • 0…100    Pa
  • 0…200    Pa   (factory default)
  • 0…500    Pa
  • 0…1000  Pa
  • 0…2500  Pa  (not to be used with Halton MDC or Halton HFS)

Operating temperature                       0 …+45ºC
Maximum overpressure                      25 kPa
Enclosure                                         IP 54, polycarbonate
Dimensions (width x height x depth)   115 x 115 x 45 mm

Measurement

The Halton MSS unit includes static type pressure measurement sensor with digital display.
Adjustable pressure measurement ranges corresponding to 0-10 VDC output signal are:

  • 0…100 Pa
  • 0…200 Pa (Factory default)
  • 0…500 Pa
  • 0…1000 Pa
  • 0…2500 Pa (Not used)

Pressure measurement range is set with jumpers according to the diagram below:

Delay selection

Pressure measurement output signal delay of 2 s is designed to be used in Halton MDC/HFS control damper and Halton MSS applications.

Measurement tubes
+  Higher pressure
–  Lower pressure

Inaccuracy of the Halton MSS is a function of measured static pressure and air velocity in ventilation duct. In undisturbed flow conditions inaccuracy is less than ± 10% when:

  • Static pressure > 40 Pa and air velocity < 6 m/s
  • Static pressure > 100 Pa and air velocity < 10 m/s

Continuous accuracy is assured by automatic zero point calibration of pressure sensor. Thus, no manual re-calibration is needed in normal operating conditions.

Specification

The casing of the measurement unit is made of galvanised steel.
The flow measurement probe pipes is made of aluminium.

The measurement unit has integral gaskets.

The unit has integrated pressure transmitter (0-10V signal) with display showing measured value.

Order code

MSS-D; PT-ZT

D  = Size of duct connection (mm)
200, 250, 315, 400, 500

Other options and accessories

PT = Difference pressure transmitter
P1     HDP-PE
P2     VRU-D3-BAC

ZT = Tailored product
N    No
Y    Yes (ETO)

Code example

MSS-200, PT=P1, ZT=N

Downloads

  • Halton MSS – Static pressure measurement unit

    Data

    en

    Shape 2
  • Halton MSS – Staattisen paineen mittausyksikkö

    Data

    fi

    Shape 2
  • Halton MSS – Section de mesure circulaire

    Data

    fr

    Shape 2
  • Halton MSS – Mätdon för mätning av statiskt tryck

    Data

    se

    Shape 2
  • Halton MSS – fr

    Data

    fr_FR
    Shape 2
Contact Us
  • Hidden
  • Max. file size: 64 MB.