Skip to content

Product / PLD

Halton PLD – Plenum for linear slot diffuser

Plenum for Halton SLL and Halton SLN diffusers

  • Ensures proper function of the supply air diffuser
  • Access for ductwork cleaning
Request a Quote

Overview

  • Plenum for connecting Halton SLL and SLN linear slot diffuser supply/exhaust unit to ductwork
  • Ensures proper function of the supply air diffuser
  • Access for ductwork cleaning

Product models and accessories

  • Detachable airflow rate measurement and balancing module available.

Dimensions

Slots H K ØD
1 235 47 160
2 275 85 200
3 275 123 200
4 325 161 250

Standard dimensions for linear slot diffusers

 Diffuser active
length (mm)
572 872 1172 1472 1772
 L (mm) 571 871 1171 1471 1771
 L1 (mm) 286 436 586 368 443
 Duct connections  (pcs) 1 1 1 2 2

In addition to standard linear slot diffuser sizes, other sizes can be ordered.
The maximum length is 2000 mm.

Continuous plenums with modular design are also available for installation lengths greater than 2000 mm.

Material

Part Material Note
Plenum box / spigot Galvanised steel Spigot equipped with
rubber  gasket
Sound attenuation
material
Mineral wool or
polyester fibre
The mineral wool
is fixed with nails

Accessories

 Accessory Code  Descritption
 Sound attenuation material 2W  Mineral wool on 2 sides
 Sound attenuation material 5W  Mineral wool on 5 sides
 Sound attenuation material 2P  Polyester fibre on 2 sides
 Sound attenuation material 5P  Polyester fibre 5 sides
 Airflow measurement and
adjustment unit
OM  For supply installation

Function

The duct pressure and air velocity are reduced inside the Halton PLD plenum box.
Air is supplied into the space through the diffuser, improving the air distribution quality.

When the Halton PLD is supplied equipped with a measurement and adjustment unit, the volume flow rate can be balanced.

Installation

Key:
1.  Plenum
2.  Measurement and adjustment module

The plenum is installed into the suspended ceiling with M8 drop rods (not supplied in the delivery).
Connect the plenum to the ductwork with a spigot equipped with an integrated rubber gasket.

When equipped with a measurement and adjustment module, the recommended safety distance upstream of the device is at least 3D, in order to ensure a reliable airflow rate measurement.

The unit s control spindle must not be excessively bent.

Adjustment

In order to enable airflow adjustment and measurement of airflow rate, it is recommended that you connect the diffuser to the plenum equipped with the MSM module.
The supply flow rate is determined by using the measurement and adjustment module MSM.

Detach the linear slot diffuser and pass the tubes and control spindle through the diffuser.
Replace the diffuser / exhaust unit.

Measure the differential pressure using a manometer. The flow rate is calculated using the formula below:

pm      Measured pressure [Pa]
k            k factor given as a function of mounting and diameter
qv          Airflow rate [l/s]

The k-factor for installations with different safety distances
(D= duct diameter)

NS > 6xD min 3xD
160 19 22
200 28 32
250 49 51

Adjust the airflow rate by rotating the control spindle until the desired setting is achieved.
Lock the damper position with a screw.

Replace the tubes and spindle into the plenum and replace the diffuser.

Servicing

Remove the measurement and adjustment module by gently pulling the shaft (not the control spindle).
Wipe the parts with a damp cloth, instead of immersing in water.

Reassemble the measurement and adjustment module by pushing the shaft back into place until the module meets the stopper.

Specification

The plenum is made of galvanised steel.

The plenum comprises an airflow measurement and adjustment module.

The diffuser is detachable in order to provide access to the measurement and adjustment module in the plenum.

The plenum reduces duct pressure and air velocity in order to supply air throughout the entire face area of the linear diffuser and improve the air distribution quality.

Order code

PLD/S-L-D-N, IN-OM-ID-ZT

S = Number of slots
1, 2, 3, 4

L = Length (mm)
372,+1,..,50000

D = Diameter of duct connection (mm)
160, 200, 250

N = Number of duct connections
1, 2, 3, 4 .., 322

Other options and accessories

IN = Sound attenuation material
N         No attenuation material
2W     2 sides, mineral wool
5W     5 sides, mineral wool
2P       2 sides, polyester fibre
5P       5 sides, polyester fibre

OM = Measurement/adjustment module (MSM)
N         No measurement or adjustment module
Y         MSM installed in each duct connection

ID  = Diffuser assembled with plenum
N          No
Y          Yes

ZT  = Tailored product
N          No
Y          Yes (ETO)

Code example

PLD/1-400-160-1, IN=N, OM=N, ZT=N

Contact Us
  • Hidden
  • Max. file size: 64 MB.