Halton KFM is a galley grease hood for use in marine & offshore applications to remove contaminated air released by cooking equipment with low heat loads.
Halton KFM is a galley grease hood for use in marine & offshore applications to remove contaminated air released by cooking equipment. The KFM hood uses Halton Capture Jet™ technology, which allows the hood to operate with up to 30% lower exhaust airflow rates than traditional hoods.
|KFM DIMENSIONS (mm)|
Note: Maintenance / light fixture hatch is as big as the construction allows.
|Main body||Stainless steel EN 1.4301 (AISI304)||1,25 mm||Option: EN 1.4404 (AISI316L)|
|Light fixture||Painted steel||–||–|
The KFM hood comprises a Capture Jet™ air supply module, a light fixture, adjustment dampers, airflow measurement taps and KSA grease filters. All parts of the hood are manufactured from polished stainless steel EN 1.4301 (AISI304). The Capture Jet™ supply plenum is thermally insulated through the use of mineral wool material to prevent condensation on the inner face above the cooking equipment. The hood is equipped with removable grease cup for collection of the grease.
*If fire or shut-off damper is located at the duct, Halton suggests two default solutions for duct connection:
The above table represents an indication of different size of average KFM hoods without Capture Jet technology. Weight does not include the fire damper.
The above table represents an indication of different size of average KFM hoods with Capture Jet technology. Weight does not include fire damper.
|RECOMMENDED EXHAUST AIRFLOW|
|NUMBER OF KSA FILTERS||MINIMUM l/s||MAXIMUM l/s||MINIMUM m3/h||MAXIMUM m3/h|
Note: KSA filter size 500x330x50 mm
The galley hoods shall be constructed from stainless steel EN 1.4301 (AISI304). The galley hoods shall be supplied complete with outer casing / main body, airflow measurement taps, exhaust air spigot connection with adjustment damper, maintenance hatch, light fixture, grease filters, grease cup. Classified fire damper in each exhaust connection. Classified fire damper in each exhaust connection is available as an option. he manufacture of all galley hoods shall be controlled by ISO 3834-2:2005, ISO 9001, 14001 and OHSAS 18001 standards. The design of hoods shall follow USPHS guidelines.
All parts shall be constructed of stainless steel sheet (thickness 1.25 mm) with a polished finish. The inside corners of the hood are rounded for easy cleanability according to USPHS guidelines. The joints at the lower edges of the device are welded. All visible screws are thumb screw type. The hood is equipped with a grease cup for removing the grease. There is a maintenance hatch in each hood for easy access above the hood.
The Capture JetTM plenum shall be insulated with sealed mineral wool. Plenum can be accessed through a maintenance hatch(es).
The hood shall be designed with Capture JetTM technology to reduce the exhaust airflow rate required and increase the capture and containment efficiencies of the hood, while reducing energy use.
Measurement taps shall be located on top of the hood for supply air and exhaust air measurement.
The KSA grease filters shall be constructed of stainless steel. The grease filters shall be supplied in modular size of 500x330x50 mm and shall be removable via two folding handles. The grease filters shall have a honeycomb design in order to allow high grease filtration efficiency with the aid of centrifugal effect in filter honeycombs.
Mechanical filtration is recommended to be used in hoods with low utilization rate and cooking process producing mainly large grease particles (> 8 microns), e.g. food prepared with gas fryers, griddles and broilers (source ASHRAE).
The duct connections and adjustment dampers for exhaust air shall be constructed from stainless steel. The dampers shall be adjustable.
Each hood shall be delivered with a fluorescent light fixtures or LED light fixtures providing approx. an average illuminance of 500 lux at the work surfaces of the cooking appliances. The light fixtures shall be suitable for a single-phase 230-VAC power supply and shall be manufactured to be of protection class IP67. The ballast and capacitor shall be located within the light frame. The core electric cables connecting the light fixture to the junction box shall be provided.The light fixture shall be installed on a hinged maintenance hatch, allowing access to the hood roof.
|L < 1250 mm, 2x24 W||720 mm||220 mm|
|L > 1250 mm, < 2000 mm, 2x39 W||1020 mm||220 mm|
|L > 2000 mm, 2×49 W||1620 mm||220 mm|
|L < 1250 mm, 1x28 W||720 mm||175 mm|
|L > 1250 mm, < 2000 mm, 1x42 W||1020 mm||175 mm|
|L > 2000 mm, 1×69 W||1620 mm||175 mm|
Each hood shall be provided with a maintenance hatch made of stainless steel with a shock- resistant plastic window. The heat tolerance of the window shall be up to +115 °C. The hatch shall be easily opened and closed. The maintenance / light fixture hatch is as big as the construction allows.
∆Pst = Static pressure loss
∆PTAB = TAB pressure for airflow rate measurement
(N) With Capture Jet
(S) Without Capture Jet
S=N: 1000-2000 S=S: 850-2000
Model S=N with Capture Jet
Model S=S without Capture Jet
(H)=Height of front end
(A) 1 sensor
(B) 2 sensors
(C) 3 sensors
(D) 4 sensors
(UB)=UV or MARVEL Box
(C) Marvel-box PL
(SS) Stainless steel EN1.4301
(AS) Stainless steel EN1.4404
(DS)=Diameter of supply connection
(A) Type SLR
(B) Type LED SLV
(FK)=Fire suppression system
(1) 1 pc
(2) 2 pcs
(3) 3 pcs
(BL) Capture Jet fan with potentiometer
(HE) Ceiling condensation removal heating